Ferrari F430 Parts & Wheel Fitment
2009 Ferrari F430 Wheel Fitment. Stored configurations: 2. Wheel diameter: 19 in. Wheel offset: 31 mm. Bolt pattern: 5×108. Vehicle hub bore: 67.1 mm. Select a stored configuration, then enter a proposed wheel. The catalog does not prove OEM approval for every row.
Stored wheel configurations are catalog reference rows. They are not labeled factory OEM unless a source row independently says so.
Stored reference coverage
Values that vary are shown as a range. Select a stored configuration before treating one row as the comparison baseline.
- Rim diameter
- 19 in
- Rim width
- 7.5–8 in
- Offset
- 31 mm
- Backspacing
- 5–5.2 in Derived from width and offset. Not a stored catalog field.
- Bolt pattern
- 5×108
- Hub / center bore
- 67.1 mm Year hub record and trim center-bore record agree.
- Thread
- M14 x 1.5
- Fastener
- Lug bolts
- Tire sizes
- 2 stored sizes
Proposed wheel
Prefill copies the selected catalog row as a starting point. Edit every field for the aftermarket wheel you want to check.
Fitment comparison
- Bolt pattern: Unknown
Select a stored configuration before treating bolt pattern as known.
- Center bore: Unknown
Enter the proposed wheel center bore to compare it with the vehicle hub.
- Wheel position: Unknown
Enter proposed width and offset, and select a stored configuration that has both values.
- Tire diameter: Unknown
Enter a proposed tire size in the form 275/65R18 to compare overall diameter.
- Brake clearance: Not verified
Brake and caliper clearance are not stored. The calculator does not verify them.
- Load rating: Not verified
Wheel load rating is not stored. No catalog row is treated as a load approval.
- Body / suspension clearance: Not verified
Fender and suspension clearance are not stored. A stored size range is not a safe-offset band.
Wheel-position diagram
The diagram needs stored and proposed width and offset. It shows geometric wheel position, not vehicle clearance.
What do you need?
Choose a job after the comparison. Calculator edits are not affiliate clicks.
Year variations
- Stored wheel configurations exist for 5 years, 2005–2009.
- Each year keeps its own catalog rows. A later bolt pattern or hub figure is not applied to an earlier year.
Questions
What wheel sizes are stored for the Ferrari F430?
Ferrari F430 in 2009 stores 2 catalog reference configurations with rim diameters of 19 in. These are stored wheel configurations, not a manufacturer-approval list.
What is the Ferrari F430 bolt pattern?
The stored bolt pattern in 2009 is 5×108. A matching bolt pattern does not guarantee the wheel fits.
What offset range is recorded for the Ferrari F430?
Stored offset in 2009 is 31 mm. That is stored reference coverage, not proof that every intermediate offset fits.
What is the Ferrari F430 hub bore?
The year hub record is 67.1 mm (auto_model_year.center_bore_id → rim_center_bore). Trim center bore is 67.1 mm (zdonor_wheel_size_trim.center_bore).
Does Ferrari F430 wheel fitment vary by year?
Wheel rows are stored for 5 years, 2005–2009. This page shows 2009. Choose another year to compare that year's stored configurations. A newer pattern is not copied onto an older year.
How does wheel width affect fitment?
Width grows the wheel on both sides of the centerline. Combined with offset it changes inner and outer lip position. That calculation does not establish fender or suspension clearance.
How does changing offset affect wheel position?
Lowering the offset number moves the wheel outward toward the fender. Raising it moves the wheel inward. Example: 8.0 in ET40 to 9.0 in ET30 moves the outer edge 22.7 mm farther toward the fender and the inner edge 2.7 mm closer to the suspension.
What happens if the wheel bore is larger than the hub?
A reducing hub-centric ring may be required. The ring is specified as wheel-bore OD × hub ID, not as the subtracted gap. The stored vehicle hub in 2009 is 67.1 mm on the year record.
Can a wheel with a smaller center bore fit?
No conventional reducing ring can make a smaller wheel bore fit over a larger hub. If the proposed bore is smaller than the 67.1 mm hub, the wheel cannot slide onto that hub.
Can I use a different bolt pattern?
A different pattern does not mount on 5×108 hardware. An adapter converts one pattern to another in one direction. It does not make the wheel safe or compatible by itself.
What does an adapter change?
An adapter changes the bolt pattern the wheel sees. Thickness also changes effective offset. This page looks up directional catalog adapters only after you choose a target pattern. No thickness is recommended.
How do spacers affect effective offset?
A spacer moves the wheel outward and lowers effective offset by about the spacer thickness. This comparison does not silently add spacer thickness to the geometry. If you want that effect, enter the resulting offset as the proposed value.
How do I compare two tire sizes?
Enter both sizes as section/aspectRrim, for example 275/65R18. The page reports overall diameter difference in millimeters, inches, and percent, plus a diameter-only speedometer estimate. That is not a tire-fitment verdict.
Does a matching tire diameter guarantee fitment?
No. Diameter is only one measurement. Width, load, speed rating, clearance, and the wheel it is mounted on are not proven by a matching number.
Can the calculator verify brake clearance?
No. Brake, caliper, load rating, and body clearance are not stored. Those checks stay marked as not verified.
What additional measurements should I check?
Confirm the installed bolt pattern, hub diameter, thread, seat type, offset, backspacing, load rating, and brake and fender clearance on the vehicle. The catalog cannot supply those missing measurements.
Does a matching bolt pattern guarantee compatibility?
No. Bolt pattern is one check. Center bore, position, tire diameter, brake clearance, load rating, and body clearance are separate.